![]() ![]() The issue can also manifest as temporary loss of USB function or complete loss of USB function requiring a plug/unplug or a docking station. The issue can manifest as temporary loss of Ethernet, for example during a Microsoft Teams or Zoom call. This issue is being addressed by appliable parties and is not controlled by Targus. There is an issue with USB function on Windows PC, especially on downstream facing Thunderbolt ports, that impacts many USB devices, not just Targus docking stations and devices. support.hp.com) should be implemented when troubleshooting or diagnosing issues. Both Windows Updates and updates advised by PC manufacturers (i.e. Most of the issues observed when using docks on Windows platforms can be solved with proper PC maintenance. It can be used by IT Departments and, in many cases, end users of Targus docks and devices. However, the guide is applicable to more than just Targus Docking Stations or even just Targus products. Make sure plz you have linux-firmware installed also.Targus has revised The Docking Stations Troubleshooting Guide for its Customer Support Team. Therefore the pertinent firmware can not be loaded unless you include it in the kernel. In your kernel config you only have 2 modules. I have tried to enable USB_CDC_COMPOSITE in the kernel, but the adapter still doesn't work.ĭo you have any suggestion to make it work? I see some differences, such as all the usbcore messages. IPv6: ADDRCONF(NETDEV_CHANGE): enx3448ed7fde42: link becomes ready usb 4-1.1: reset SuperSpeed USB device number 4 using xhci_hcd usbcore: registered new interface driver r8153_ecm usbcore: registered new interface driver cdc_ether usbcore: registered new interface driver r8152 usb 4-1.1: new SuperSpeed USB device number 4 using xhci_hcd usb 4-1: new SuperSpeed USB device number 3 using xhci_hcd usb 4-1: device not accepting address 2, error -71 usbcore: registered new interface driver usbhid pcieport 0000:00:1b.0: PME: Spurious native interrupt! In that case, it is using kernel version 5.13.0-19 with the following config file:Īnd these are the dmesg messages I get when plugging first the USB-C adapter and then the ethernet cable: However, the adapter works fine when booting the laptop from a live Ubuntu 21.10 USB drive. I am in kernel version 5.17.14, and this is my kernel config file: usb 4-1.1: reset SuperSpeed USB device number 9 using xhci_hcd usb 4-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=6 usb 4-1.1: New USB device found, idVendor=0bda, idProduct=8153, bcdDevice=30.00 usb 4-1.1: new SuperSpeed USB device number 9 using xhci_hcd usb 4-1: new SuperSpeed USB device number 8 using xhci_hcd usb 4-1: device not accepting address 7, error -71 usb 4-1: Device not responding to setup address. xhci_hcd 0000:3a:00.0: WARN Set TR Deq Ptr cmd failed due to incorrect slot or ep state. usb 1-5.3: Manufacturer: Silicon Laboratories usb 1-5.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 ![]() usb 1-5.3: New USB device found, idVendor=10c4, idProduct=f407, bcdDevice= 1.00 usb 1-5.3: new full-speed USB device number 6 using xhci_hcd ucsi_acpi USBC000:00: UCSI_GET_PDOS returned 0 bytes usb 4-1: USB disconnect, device number 2 usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=49.70 ![]() usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 4-1: New USB device found, idVendor=05e3, idProduct=0617, bcdDevice=49.70 usb 1-5: new high-speed USB device number 5 using xhci_hcd usb 4-1: new SuperSpeed USB device number 2 using xhci_hcd When I plug the USB-C adapter first, and then the ethernet cable, I have the following messages in dmesg: I remember it was a bit of a pain to make it work in the first place, but if worked in the end. I have not used it for some time, and now the ehternet connection (Realtek RTL8153) does not work anymore. This is how I made it work around 2 years ago: I have a Dell DA200 USB-C to HDMI, VGA, Ethernet and USB 3.0 adapter. Posted: Sat 9:57 am Post subject: Ethernet connection of Dell DA200 not working Gentoo Forums Forum Index Kernel & Hardware Gentoo Forums :: View topic - Ethernet connection of Dell DA200 not workingĮthernet connection of Dell DA200 not working ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |